其中止回閥就屬于這種類型的閥門，它包括旋啟式止回閥和昆山良工閥門升降式止回閥。昆山良工閥門旋啟式止回閥有一介鉸鏈機構，還有一個像門一樣的閥瓣自由地靠在傾斜的閥座表面上。為了確保閥瓣每次都能到達閥座面的合適位置，閥瓣設計在鉸鏈機構，以便閥瓣具有足夠有旋啟空間，并使閥瓣真正的、全面的與閥座接觸。閥瓣可以全部用金屬制成，也可以在金屬上鑲嵌皮革、橡膠、或者采用合成覆蓋面，這取決于使用性能的要求。旋啟式止回閥在完全打開的狀況下，流體壓力幾乎不受阻礙，因此通過閥門的壓力降相對較小。升降式止回閥的閥瓣座落位于閥體上閥座密封面上。此閥門除了閥瓣可以自由地升降之外，其余部分如同截止閥一樣，流體壓力使閥瓣從閥座密封面上抬起，介質回流導致閥瓣回落到閥座上，并切斷流動。根據使用條件，閥瓣可以是全金屬結構，也可以是在閥瓣架上鑲嵌橡膠墊或橡膠環的形式。像截止閥一樣，流體通過升降式止回閥的通道也是狹窄的，因此通過升降式止回閥的壓力降比旋啟式止回閥大些，而且旋啟式止回閥的流量受到的限制很少。
Check valves belong to this type of valve, including swing check valves and Kunshan Lianggong valve lift check valves. The Kunshan Lianggong valve swing check valve has a hinge mechanism and a gate like valve disc that freely rests on the tilted valve seat surface. In order to ensure that the valve disc can reach the appropriate position on the valve seat surface every time, the valve disc is designed in a hinge mechanism, so that the valve disc has sufficient swing space and truly and comprehensively contacts the valve seat. The valve disc can be made entirely of metal, or it can be embedded with leather, rubber, or a synthetic cover on the metal, depending on the performance requirements. When the swing check valve is fully open, the fluid pressure is almost unobstructed, so the pressure drop through the valve is relatively small. The disc seat of the lift check valve is located on the sealing surface of the valve seat on the valve body. Except for the free lifting and lowering of the valve disc, the rest of this valve is like a globe valve. Fluid pressure lifts the valve disc from the sealing surface of the valve seat, and the medium backflow causes the valve disc to fall back onto the valve seat, cutting off flow. According to the usage conditions, the valve disc can be an all metal structure, or it can be in the form of embedded rubber pads or rings on the valve disc holder. Like globe valves, the passage of fluid through lift check valves is also narrow, so the pressure drop through lift check valves is greater than that of swing check valves, and the flow rate of swing check valves is limited very little.
止回閥常見故障及處理方法常見故障有：
Common faults and handling methods of check valves include:
①閥瓣打碎
① Broken valve disc
②介質倒流。
② Media backflow.
引起閥瓣打碎的原因是：
The cause of valve disc breakage is:
止回閥前后介質壓力處于接近平衡而又互相“拉鋸”的狀態，昆山良工閥門閥瓣經常與閥座拍打，某些脆性材料(如鑄鐵、黃銅等)做成的閥瓣就被打碎。預防的辦法是采用閥瓣為韌性材料的止回閥。
The medium pressure before and after the check valve is in a state of close balance and mutual "sawing". The valve disc of Kunshan Lianggong valve often beats against the valve seat, and the valve disc made of some brittle materials (such as cast iron, brass, etc.) is broken. The preventive method is to use a check valve with a resilient disc material.
介質倒流的原因有：
The reasons for media backflow include:
①密封面破壞
① Damaged sealing surface
②夾入雜質。
② Inclusion of impurities.
修復密封面和清洗雜質，就能防止倒流。
Repairing the sealing surface and cleaning impurities can prevent backflow.
企業公告：
